NAVY - SH - Naval Sea Systems Command (Ship Systems): Recent submissions
Now showing items 601-620 of 2792
-
A-A-59470
Abstract: This commercial item description (CID) describes modular drawer storage cabinets with various combinations of drawer sizes in various sizes of cabinet housings to be used for storing parts, tools, and supplies for Naval ... -
MIL-R-23098A
Abstract: This specification covers general requirements for single phase, 400 Hertz (Hz) alternating current (a.c.) line voltage requlators intended for shipboard application. The single-phase regulators shall operate in a three-phase ... -
MIL-E-22200/10C
Abstract: This specification covers iron-powder, low-hydrogen types of covered electrodes for the fabrication and repair welding of low and medium carbon, high tensile, and higher-strength low-alloy steels for as-welded and ...Subject(s) : Dynamic tear , Elongation , HSLA-80 and -100 steel , HY-80 and -100 steel , Moisture resistant , Stress-relieved , Yield strength , -
A-A-59002/1
Abstract: This Commercial Item Description covers requirements for an interior shipboard announcing loudspeaker. -
MIL-L-24560/3A
Abstract: This specification sheet is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.
The complete requirements ... -
MIL-PRF-16552F VALID NOTICE 1
Abstract: This specification covers air filters of permanent and cleanable types. They are for use in filtering dust and lint from the air passing through ventilating, heating and cooling systems. Intended Use: The ...Subject(s) : Air filters , Air filters , nonmagnetic , -
A-A-59191
Abstract: This commercial item description (CID) covers counter-mounted automatic coffee urns intended for brewing coffee and dispensing coffee and hot water for Naval shipboard use. -
A-A-59441/4
Abstract: This commercial item description covers the requirements for Type IV VCIs to provide corrosion protection for metals used in mechanical, electrical and electronic components and equipment that are subjected to corrosive ... -
TT-R-266D
Abstract: This specification covers alkyd resin solutions for use in paints and enamels. Intended Use: The alkyd resin solutions covered by this specification are intended for use in paints and enamels. The resin ... -
MIL-F-24704/2A
Abstract: This specification sheet covers the requirements for four bolt square butt weld flanges for use in 3000 pounds per square inch (lb/in2) hydraulic systems. -
MS17046 REV B
Abstract: This standard has been approved by the Bureau of Ships Department of the Navy and is mandatory for use by that activity. All other military activities are required to employ this standard where suitable. -
MIL-M-16125C
Abstract: This specification covers switchboard and portable electrical frequency meters for use in presenting visually the frequency of 60 or 400 cycle per second electric power system by a marked dial and pointer.
The type ... -
DOD-HDBK-289
Abstract: This handbook establishes standard design requirements and procedures, and identifies the configurations and applications of lighting systems on naval ships.
These criteria apply to new construction only when invoked ...Subject(s) : Candlepower , Footcandle , Illumination , blue , Illumination , red , Lamps , Lighting , Lunun output , -
MIL-PRF-24755B
Abstract: This specification covers high pressure vaneaxial fans used in collective protective systems for Naval shipboard ventilation systems. Intended Use: The fan-motor units specified herein are intended for ...Subject(s) : Blade , Casing , Duct , Impeller , Vane , -
MIL-H-21367/19
Abstract: This specification is approved for use within the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring ... -
MIL-P-23469D
Abstract: This specification covers metal fasteners of the pull-tool type, each comprising a headed, grooved pin secured by a collar swaged into the grooves, and for installation without bucking more than manual restraint on the ...Subject(s) : Headed , Metal fasteners , Pull joint surfaces , Tensile strength fastening ,

درباره ما