درباره ما
CSA S157-05/S157.1-05
Strength design in aluminum/ Commentary on CSA S157-05, Strength design in aluminum - Fourth Edition; Update No. 1: February 2007; Update No. 2: April 2007; Update No. 3: July 2009
Organization:
CSA - CSA Group
Year: 2010
Abstract: This Standard applies to the design of aluminum alloy members and assemblies intended to carry a known load.
This Standard specifies requirements for the design of members to meet the requirements of the National Building Code of Canada using limit states design procedures.
This Standard contains rules to determine the ultimate resistance of aluminum members and connections, and may be used for the design of aluminum assemblies in general.
Where members designed in accordance with this Standard are intended for use in structures for which other standards apply, this Standard supplements such standards, as applicable.
Note: Annex A lists some applications to which other standards apply.
Where this Standard does not provide design expressions or dimensional limitations that are applicable to a specific situation, a rational design may be used, based on appropriate theories, tests, analyses, or engineering experience.
Note: See Annex B for common uses of alloys.
In CSA Standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
The expressions contained herein are dimensionally uniform, and any consistent system of units may be employed. Where dimensions are identified, SI units are used. Evaluation is normally conducted in newtons (N) for force, millimetres (mm) for length, and megapascals (MPa = N/mm2) for stress.
This Standard specifies requirements for the design of members to meet the requirements of the National Building Code of Canada using limit states design procedures.
This Standard contains rules to determine the ultimate resistance of aluminum members and connections, and may be used for the design of aluminum assemblies in general.
Where members designed in accordance with this Standard are intended for use in structures for which other standards apply, this Standard supplements such standards, as applicable.
Note: Annex A lists some applications to which other standards apply.
Where this Standard does not provide design expressions or dimensional limitations that are applicable to a specific situation, a rational design may be used, based on appropriate theories, tests, analyses, or engineering experience.
Note: See Annex B for common uses of alloys.
In CSA Standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
The expressions contained herein are dimensionally uniform, and any consistent system of units may be employed. Where dimensions are identified, SI units are used. Evaluation is normally conducted in newtons (N) for force, millimetres (mm) for length, and megapascals (MPa = N/mm2) for stress.
Collections
:
-
Statistics
CSA S157-05/S157.1-05
Show full item record
| contributor author | CSA - CSA Group | |
| date accessioned | 2017-09-04T18:19:21Z | |
| date available | 2017-09-04T18:19:21Z | |
| date copyright | 2005.02.01 (R 2010) | |
| date issued | 2010 | |
| identifier other | HTXJWCAAAAAAAAAA.pdf | |
| identifier uri | http://mapnamagz.yabesh.ir/std;query=authoF23793FDFCDCAC4/handle/yse/202079 | |
| description abstract | This Standard applies to the design of aluminum alloy members and assemblies intended to carry a known load. This Standard specifies requirements for the design of members to meet the requirements of the National Building Code of Canada using limit states design procedures. This Standard contains rules to determine the ultimate resistance of aluminum members and connections, and may be used for the design of aluminum assemblies in general. Where members designed in accordance with this Standard are intended for use in structures for which other standards apply, this Standard supplements such standards, as applicable. Note: Annex A lists some applications to which other standards apply. Where this Standard does not provide design expressions or dimensional limitations that are applicable to a specific situation, a rational design may be used, based on appropriate theories, tests, analyses, or engineering experience. Note: See Annex B for common uses of alloys. In CSA Standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. The expressions contained herein are dimensionally uniform, and any consistent system of units may be employed. Where dimensions are identified, SI units are used. Evaluation is normally conducted in newtons (N) for force, millimetres (mm) for length, and megapascals (MPa = N/mm2) for stress. | |
| language | English | |
| title | CSA S157-05/S157.1-05 | num |
| title | Strength design in aluminum/ Commentary on CSA S157-05, Strength design in aluminum - Fourth Edition; Update No. 1: February 2007; Update No. 2: April 2007; Update No. 3: July 2009 | en |
| type | standard | |
| page | 200 | |
| status | Active | |
| tree | CSA - CSA Group:;2010 | |
| contenttype | fulltext |