درباره ما
AASHTO R 72
Standard Practice for Match Curing of Concrete Test Specimens
Year: 2016
Abstract: This recommended practice covers procedures for making and curing cylindrical concrete specimens at the same temperature as that measured in a concrete member.
The concrete sample used to make the specimens shall be taken from the concrete being placed in the same member where the temperature is to be measured.
This procedure can be deployed with confidence for both air chamber and insulated jacket (Surecure) systems and for both molded cylinders with nominal diameter to height dimensions of 100 by 200 mm (4 by 8 in.) or 150 by 300 mm (6 by 12 in.). However, users should be watchful of Type I error for air chamber systems and Type II error with insulated jacket mold systems. A Type I error represents the situation where loss of temperature control occurs over only a portion of the entire match-cure duration where control is later regained. A Type II error represents the situation where a constant level of temperature control error occurs during the entire match-cure duration.
The values stated in SI units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
The concrete sample used to make the specimens shall be taken from the concrete being placed in the same member where the temperature is to be measured.
This procedure can be deployed with confidence for both air chamber and insulated jacket (Surecure) systems and for both molded cylinders with nominal diameter to height dimensions of 100 by 200 mm (4 by 8 in.) or 150 by 300 mm (6 by 12 in.). However, users should be watchful of Type I error for air chamber systems and Type II error with insulated jacket mold systems. A Type I error represents the situation where loss of temperature control occurs over only a portion of the entire match-cure duration where control is later regained. A Type II error represents the situation where a constant level of temperature control error occurs during the entire match-cure duration.
The values stated in SI units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Show full item record
| contributor author | AASHTO - American Association of State Highway and Transportation Officials | |
| date accessioned | 2017-09-04T18:45:52Z | |
| date available | 2017-09-04T18:45:52Z | |
| date copyright | 2016.01.01 | |
| date issued | 2016 | |
| identifier other | KIEAPFAAAAAAAAAA.pdf | |
| identifier uri | http://mapnamagz.yabesh.ir/std;query=autho4A5893/handle/yse/227205 | |
| description abstract | This recommended practice covers procedures for making and curing cylindrical concrete specimens at the same temperature as that measured in a concrete member. The concrete sample used to make the specimens shall be taken from the concrete being placed in the same member where the temperature is to be measured. This procedure can be deployed with confidence for both air chamber and insulated jacket (Surecure) systems and for both molded cylinders with nominal diameter to height dimensions of 100 by 200 mm (4 by 8 in.) or 150 by 300 mm (6 by 12 in.). However, users should be watchful of Type I error for air chamber systems and Type II error with insulated jacket mold systems. A Type I error represents the situation where loss of temperature control occurs over only a portion of the entire match-cure duration where control is later regained. A Type II error represents the situation where a constant level of temperature control error occurs during the entire match-cure duration. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. | |
| language | English | |
| title | AASHTO R 72 | num |
| title | Standard Practice for Match Curing of Concrete Test Specimens | en |
| type | standard | |
| page | 5 | |
| status | Active | |
| tree | AASHTO - American Association of State Highway and Transportation Officials:;2016 | |
| contenttype | fulltext |