درباره ما
ASME - ASME International: Recent submissions
Now showing items 601-620 of 1083
-
ASME B18.31.5
Abstract: This Standard establishes general requirements for parts classified as bent bolts. Dimensional requirements are provided in tables for U-bolts of differing bends, eyebolts, hook bolts of differing bends, and J-bolts. General ... -
ASME MFC-8M
Abstract: This Standard describes the practices and means which allow the pressures at a head type primary device to be conveyed to the secondary device in a flow measurement system without introducing unnecessary measurement ... -
ASME B18.2.3.9M
Abstract: (a) This Standard covers the complete dimensional and general data for metric series heavy hex flange screws recognized as American National Standard.
(b) The inclusion of dimensional data in this Standard is ... -
ASME B89.1.5
Abstract: This Standard is intended to establish uniform practices for the measurement of master discs or cylindrical plug gages to a given tolerance using vertical or horizontal comparators and laser instruments. The Standard ... -
ASME B1.9
Abstract: This standard relates to screw threads of buttress form and provides:
(a) A form of 7°/45° buttress thread with 0.6p basic height of thread engagement (see Fig. 1a).
(b) A table of preferred ... -
ASME MFC-26
Abstract: This Standard applies only to the steady flow of single-phase gases and gas mixtures and applies only to bellmouth inlet flowmeters in which the flow remains subsonic throughout the measuring section and the flow is steady ... -
ASME B30.9
Abstract: SCOPE EXCLUSIONS
Any exclusion of, or limitations applicable to the equipment, requirements, recommendations, or operations contained in this Standard are established in the affected volume's scope. ... -
ASME A112.4.2
Abstract: This Standard establishes general and performance requirements, test methods, and marking requirements for bidet sprays and other optional features as applied to water closets, water closet seats, and other retrofit devices. ... -
ASME B18.31.1M
Abstract: This Standard covers the complete dimensional and general data for continuous-thread and double-end metric series studs recognized as an American National Standard. The following configurations are covered:
conti ... -
ASME A17.4
Abstract: It is recommended that any evacuation of passengers from elevator cars be performed under the direct supervision of elevator personnel, as their experience and expertise assure the resourcefulness necessary to cope ... -
ASME PTC 30.1
Abstract: OBJECT AND SCOPE
The scope of this Code covers, but is not limited to, the testing of mechanical draft heat exchangers, of both the forced draft and induced draft types; natural draft heat exchangers; and fan ... -
ASME STP-PT-031
Abstract: The purpose of this study is to begin the process of developing an appropriate and accurate method of predicting fatigue failure due to internal pressure loading in piping components. Historically, piping component fatigue ... -
ASME QME-1
Abstract: GENERAL
ASME QME-1 is divided into sections that are designated by capital letters: the letter Q, which stands for qualification, followed by a second letter that generally indicates the subject matter ... -
ASME STP-NU-044
Abstract: INTRODUCTION
This section describes the Task 12 scope of work and the approaches used to address the scope of work. -
ASME B27.7
Abstract: This standard is intended to cover complete general and dimensional data for three series of general purpose tapered and reduced cross section retaining rings which may be used with the nominal size shafts and housings ... -
ASME B40.100
Abstract: FOREWORD
ASME Standards Committee B40 is comprised of a balanced cross section of pressure gauge users, manufacturers, and interested members representing governmental agencies, testing laboratories, ... -
ASME B18.8.1
Abstract: This Standard covers the complete dimensional and general data for clevis pins sizes 3⁄16 in. through 2 in. and cotter (split) pins sizes 1⁄32 in. through ... -
ASME B1.15 ERTA
Abstract: This Standard establishes the basic triangular profile for the UNJ thread form, provides a system of designations, lists the standard series of diameter-pitch combinations for diameters from 0.600 to 6.000 in., and specifies ... -
ASME B1.30
Abstract: The American National Standards Committee B1 for standardization of screw threads was organized in 1920 as sectional Committee B1 under the sponsorship of the American Engineering Standards Committee (later the American ...