درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 841-860 of 39933
-
Standard Specification for Carbon Steel Eyebolts
Abstract: This specification covers the chemical, mechanical, grain size, and dimensional requirements for weldless forged, quenched, and tempered carbon steel threaded lifting eyes (formerly pertained to as eyebolts) for overhead ... -
Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
Abstract: 3.1 The modulus of rupture of carbon-containing refractories at elevated temperatures has become accepted as a useful measurement in quality control testing and in research and development. These measurements are also used ... -
Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation
Abstract: This specification covers glass fiber unsupported needled felt binder-free thermal insulations. This material is used as the thermal insulation component in the fabrication of insulation systems for use on machinery and ... -
Standard Specification for Spun Cast Prestressed Concrete Poles
Abstract: This specification covers spun cast prestressed concrete poles for use as structural supports for streetlights, traffic signals, and transmission, distribution, and communication lines. The acceptability of the poles shall ... -
Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
Abstract: This specification covers heat-treated flat glass - kind HS, kind FT coated and uncoated glass used in general building construction. Glass furnished under this specification shall be of the following conditions: condition ... -
Standard Specification for Flat Glass
Abstract: This specification covers the quality requirements of flat, transparent, clear, and tinted glass. This glass is intended to be used primarily for architectural glazing products including: coated glass, insulating glass ... -
Standard Test Method for Sampling and Testing Grout for Masonry
Abstract: 3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement. 3.1.1 During construction, grout is placed within or between absorptive masonry units. ... -
Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation
Abstract: This specification covers the types and physical properties of spray applied rigid cellular polyurethane intended for use as thermal insulation. Spray-applied rigid-cellular polyurethane thermal insulation shall be classified ... -
Standard Practice for Installation of Cellulosic and Mineral Fiber Loose-Fill Thermal Insulation
Abstract: 4.1 This practice recognizes that effectiveness, safety, and durability of insulation depend not only on the quality of the insulating materials, but also on their proper installation. 4.2 Improper installation of insulation ... -
Standard Specification for Uranium Hexafluoride Enriched to Less Than 5 % 235U
Abstract: This specification covers nuclear grade uranium hexafluoride (UF6) that has been processed through an enrichment plant or produced by blending highly enriched uranium with other uranium to produce a concentration suitable ... -
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
Abstract: This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel ... -
Standard Test Method for Photoelastic Determination of Residual Stress in a Transparent Glass Matrix Using a Polarizing Microscope and Optical Retardation Compensation Procedures
Abstract: 5.1 The quality and performance of an article of glassware may be affected not only by the presence of residual stresses due to heat treatment above the strain point in the ware, but also by additional residual stresses ... -
Standard Specification for Slag Cement for Use in Concrete and Mortars
Abstract: This specification covers three strength grades of finely ground granulated blast-furnace slag (Grades 80, 100, and 120) for use as a cementitious material in concrete and mortars. The slag shall contain no additions and ... -
Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Integral Wearing Surface
Abstract: This specification describes the required properties and test methods for high-solids content, cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks not subject to hydrostatic ... -
Standard Classification of Potential Health and Safety Concerns Associated With Thermal Insulation Materials and Accessories
Abstract: 4.1 The purpose of this classification is to identify potential concerns and effects which may occur during the life cycle (installation, service, removal, and disposal) of insulation materials and accessories resulting ... -
Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast
Abstract: This specification covers the general requirements for statically cast prestressed concrete poles intended for use as structural supports for lights, distribution, transmission and dead end poles. The products made up of ... -
Standard Test Method for Porosity in Vitreous Whitewares by Dye Penetration
Abstract: 5.1 This test method provides a means for readily determining if a ceramic is properly fired (matured). Penetration of any extent may negate the usefulness of the ceramic, or, arbitrarily, some degree of penetration may ...